|
... more info
|
Pro-M Cold Air Screen
Price: $24.99
|
|
Pro-M Mass Air Meter Screen used for Cold Air Calibrations. This screen does not create a "Cold Air Calibration" . Note: This is a replacement only |
|
|
Wiring Harness Relay and Fuse Block
Price: $99.95
|
|
The wiring harness relay block features a single location of relays and fuses for the stand alone EFI wiring harness. This relay block also features ... more info |
|
|
Walbro 255 Liter per Hour External Fuel Pump
Price: $199.99
|
|
These Walbro high pressure inline fuel pumps have a lightweight compact design that fits most EFI applications including turbo and supercharged, and ... more info |
|
|
Idle Air Controller
Price: $64.99
|
|
Idle air control valves help you get maximum fuel efficiency and power from your engine. A properly operating idle air control valve is an essential ... more info |
|
|
Inertia Switch
Price: $29.99
|
|
The Inertial Switch is a switch, firmly mounted upon a vehicle, that senses shock or vibration. It is a part of electrical circuits that may either ... more info |
|
|
O2 Sensors - Oxygen Sensor
Price: $39.99
|
|
An O2 Sensor (Oxygen Sensor) is attached to a vehicle's exhaust system. The purpose of the O2 sensor is to measure the air to fuel ratio. In other ... more info |
|
|
O2 Sensor Weld on Bungs - Exhaust
Price: $9.99
|
|
These bungs are made to be welded on your exhaust system for proper fit and seal of the O2 Sensors. |
|
|
Air Charge Temperature Sensor
Price: $24.99
|
|
The Air Charge Temperature (ACT) Sensor is a thermal transistor. Because the ACT is mounted into the incoming air stream it changes resistance in ... more info |
|
|
Engine Coolant Temperature (ECT) Sensor
Price: $24.99
|
|
The Engine Coolant Temperature (ECT) Sensor is a thermal transistor. Because the ECT is in direct contact with the engine coolant flow it changes ... more info |
|
|
Throttle Position Sensor
Price: $29.99
|
|
A throttle position sensor (TPS) is a sensor used to monitor the position of the throttle in an internal combustion engine. The sensor is usually ... more info |
|
|
Barometric Pressure Sensor
Price: $79.99
|
|
The Barometric Pressure sensor is used to sense the changes in barometric pressure, allowing the computer to sense the altitude at which the vehicle ... more info |
|
|
Pro-M Conical Bullet Filter
Price: $44.99
|
|
This is the high flow conical air filter for the 75mm Plastic Bullet and the 75mm Chrome Bullet. |
|
|
1000 CFM Throttle Body with TPS
Price: $549.99
|
|
1000 CFM 4 bbl throttle body. It features all aluminum and stainless steel construction, sealed ball bearings on the throttle shafts, and progressive ... more info |
|
... more info
|
Repairs for Other Brands
Price: $200.00
|
|
If the electronics on your meter assembly are physically damaged, or are no longer working, you can send the meter in for repair. The electronics ... more info |
|
... more info
|
Ford Factory Meter Repair
Price: $200.00
|
|
If the electronics on your meter assembly are physically damaged, or are no longer working, you can send the meter in for repair. The electronics ... more info |
|
... more info
|
Pro-M Meter Repair
Price: $175.00
|
|
If the electronics on your meter assembly are physically damaged, or are no longer working, you can send the meter in for repair. The electronics ... more info |
|
... more info
|
Recalibrations for Other Brands
Price: $150.00
|
|
If you are changing injector size, or installing your mass air meter into a different vehicle, you will need to get your meter recalibrated. We will ... more info |
|
|
Pro-M Slot-In Sensor Wiring Harness
Price: $39.99
|
|
This is the harness connector for the Pro-M Slot-In Sensor. Wire leads are 3 feet long to give the installer some flexibility in the location of the ... more info |
|
... more info
|
Drop-In Sensor Weld-On Flange
Price: $49.99
|
|
Use this weld on flange with our Drop-In sensor to create your own custom mass air meter assembly. Available in either steel or aluminum (choose ... more info |
|
... more info
|
Pro-M Drop-in Sensor
Price: $174.99
|
|
Use the Pro-M Drop-In Sensor with our Drop-In weld-on flange to create your own custom mass air meter assembly. The new assembly will need to be ... more info |
|
